ASTM A1016/A1016M-18a PDF Download
Standard EN Sample
Standard Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes
Also Known As:
Abstract
This specification covers general requirements for ferritic alloy steel, austenitic alloy steel, and stainless steel tubes. The steel shall made by any process. The material shall conform to the tensile property requirements prescribed in the individual product specification. Yield strength tests and elongation tests shall be made to conform to the requirements. Flattening test, reverse flattening test, reverse bend test, flaring test, flange test, hardness test, ultrasonic test, eddy current test, flux leakage test, and hydrostatic test shall be made to conform to the requirements specified.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification covers a group of requirements that, unless otherwise specified in an individual specification, shall apply to the ASTM product specifications noted below.
| Title of Specification | ASTM |
|
|
|
| Seamless Carbon-Molybdenum Alloy-Steel Boiler and | A209/A209M |
| Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, | A213/A213M |
| Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, | A249/A249M |
| Electric-Resistance-Welded Ferritic Alloy-Steel Boiler and | A250/A250M |
| Seamless and Welded Ferritic and Martensitic Stainless Steel | A268/A268M |
| Seamless and Welded Austenitic Stainless Steel Tubing for | A269/A269M |
| Seamless and Welded Austenitic and Ferritic/Austenitic | A270/A270M |
| Seamless and Welded Carbon and Alloy-Steel Tubes for | A334/A334M |
| Welded Austenitic Stainless Steel Feedwater Heater Tubes | A688/A688M |
| Austenitic Stainless Steel Tubing for Breeder Reactor Core | A771/A771M |
| Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing | A789/A789M |
| Seamless and Welded Ferritic Stainless Steel Feedwater Heater | A803/A803M |
| Seamless Austenitic and Martensitic Stainless Steel Duct | A826/A826M |
| High-Frequency Induction Welded, Unannealed, Austenitic | A851 |
| Welded Austenitic Alloy Steel Boiler, Superheater, Condenser, | A1098/A1098M |
1.2 In the case of conflict between a requirement of a product specification and a requirement of this general requirements specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this general requirements specification and a more stringent requirement of the purchase order, the purchase order shall prevail.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation (SI) of the product specification is specified in the order.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Descriptors | duplex stainless steel, stainless steel tubes, seamless steel tubes, welded steel tubes,Austenitic Stainless Steel,Duplex and Super Duplex Stainless Steel,Ferritic Stainless Steel,Seamless Pipes and Tubes,Tubular Products,Welded Pipes and Tubes |
| ICS Codes | 77.140.20 - Stainless steels |
| Language(s) | English |
| File Size | 163.8 KB |
